Accessories for the 3D Sets Landy
Mike Thomas
Created , last modified
3D SetsRemote Control
Table of contents
Intro
Printing Upgrades and Accessories for the 3D Sets Landy.
Rock Sliders and Grill
Image © 2022 3D Sets
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Fan | 1 | eSun ABS+ (Silver) | ❌ | |
| Grill with light protection | 1 | eSun ABS+ (Black) | ❌ | |
| Rock Slider A - left | 1 | eSun ABS+ (Black) | ❌ | |
| Rock Slider A - right | 1 | eSun ABS+ (Black) | ❌ |
Car Hauler
Printing parts for the 3D Sets Car Hauler.
Image © 2022 3D Sets
Sourcing Parts
Motion
| Item | Quantity | Received | Notes |
|---|---|---|---|
| Ball Bearing 10x15x4 mm - 6700RS | 8 | 100 | |
| Rubber tires - OD: 90-100mm, ID: 46-48mm | 4 | 4 | |
| Shock/Coil springs - 55-75mm | 4 | 4 |
Fasteners
| Item | Quantity | Received | Notes |
|---|---|---|---|
| M2x6 SHCS | 80 | 250 | |
| M2x8 SHCS | 4 | 50 | |
| M2x10 SHCS | 5 | 100 | |
| M2x12 SHCS | 24 | 50 | |
| M3x6 BHCS | 4 | 39 | |
| M3x8 BHCS | 16 | 91 | |
| M3x10 BHCS | 40 | 100 | |
| M3x12 BHCS | 18 | 147 | |
| M3x16 BHCS | 26 | 135 | |
| M3x20 BHCS | 1 | 25 | |
| M3x6 SHCS | 4 | 10 | |
| M3 nuts | 13 | 42 | |
| M5x12 SHCS | 1 | 10 |
Printing Parts
Chassis 1
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Chassis - front | 1 | eSun ABS+ (Silver) | ❌ | |
| Chassis Connector - front | 1 | eSun ABS+ (Silver) | ❌ | |
| Pole | 1 | eSun ABS+ (Silver) | ❌ |
Chassis 2
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Chassis - center | 1 | eSun ABS+ (Silver) | ❌ | |
| Chassis Connector | 2 | eSun ABS+ (Silver) | ❌ |
Chassis 3
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Chassis - rear | 1 | eSun ABS+ (Silver) | ❌ | |
| Chassis Connector | 1 | eSun ABS+ (Silver) | ❌ |
Chassis 4
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Chassis - front left | 1 | eSun ABS+ (Silver) | ❌ | |
| Chassis - front right | 1 | eSun ABS+ (Silver) | ❌ | |
| Chassis - rear left | 1 | eSun ABS+ (Silver) | ❌ | |
| Chassis - rear right | 1 | eSun ABS+ (Silver) | ❌ |
Truss 1
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Side Truss - front left | 1 | eSun ABS+ (Silver) | ❌ | |
| Side Truss - front right | 1 | eSun ABS+ (Silver) | ❌ | |
| Side Insert - stripes | 2 | eSun ABS+ (Cold White) | ❌ |
Tip
Stripes on the Side Insert can be achieved by making a Filament Change (M600) at layer 12.
Truss 2
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Front Strut - left | 1 | eSun ABS+ (Silver) | ❌ | |
| Front Strut - right | 1 | eSun ABS+ (Silver) | ❌ | |
| Front Truss - center | 1 | eSun ABS+ (Silver) | ❌ | |
| Front Truss - left | 1 | eSun ABS+ (Silver) | ❌ | |
| Front Truss - right | 1 | eSun ABS+ (Silver) | ❌ |
Truss 3
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Side Truss - rear left | 1 | eSun ABS+ (Silver) | ❌ | |
| Side Truss - rear right | 1 | eSun ABS+ (Silver) | ❌ | |
| Side Insert Rear - stripes | 2 | eSun ABS+ (Cold White) | ❌ |
Tip
Stripes on the Side Insert can be achieved by making a Filament Change (M600) at layers 9 & 12.
Fender 1
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Fender - left | 1 | eSun ABS+ (Black) | ❌ | |
| Side Truss - center | 1 | eSun ABS+ (Silver) | ❌ |
Fender 2
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Fender - right | 1 | eSun ABS+ (Black) | ❌ | |
| Side Truss - center | 1 | eSun ABS+ (Silver) | ❌ |
Rear Bumper 1
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Light - left | 1 | BasicFil PETG (Clear) | ❌ | |
| Light - right | 1 | BasicFil PETG (Clear) | ❌ | |
| Rear Bumper - left | 1 | eSun ABS+ (Silver) | ❌ | |
| Rear Bumper - right | 1 | eSun ABS+ (Silver) | ❌ |
Tip
Indicator and Brake lights can be added by making a Filament Change (M600) at layers 47 & 49.
Rear Bumper 2
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Licence Plate | 1 | eSun ABS+ (Cold White) | ❌ |
Tip
Text can be added to the Licence Plate by making a Filament Change (M600) at layer 23.
Floor
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Floor - center front | 1 | eSun PLA (Wood) | ❌ | |
| Floor - front left | 1 | eSun PLA (Wood) | ❌ | |
| Floor - front right | 1 | eSun PLA (Wood) | ❌ | |
| Floor - center rear | 1 | eSun PLA (Wood) | ❌ | |
| Floor - rear left | 1 | eSun PLA (Wood) | ❌ | |
| Floor - rear right | 1 | eSun PLA (Wood) | ❌ |
Axle 1
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Axle Arm A | 2 | eSun ABS+ (Red) | ❌ | |
| Axle Arm B - left | 2 | eSun ABS+ (Red) | ❌ | |
| Axle Arm C | 2 | eSun ABS+ (Red) | ❌ | |
| Axle Shaft | 2 | eSun ABS+ (Black) | ❌ | |
| Axle Washer | 2 | eSun ABS+ (Black) | ❌ | |
| Ball Joint | 4 | eSun ABS+ (Black) | ❌ |
Axle 2
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Axle Arm A | 2 | eSun ABS+ (Red) | ❌ | |
| Axle Arm B - right | 2 | eSun ABS+ (Red) | ❌ | |
| Axle Arm C | 2 | eSun ABS+ (Red) | ❌ | |
| Axle Shaft | 2 | eSun ABS+ (Black) | ❌ | |
| Axle Washer | 2 | eSun ABS+ (Black) | ❌ | |
| Ball Joint | 4 | eSun ABS+ (Black) | ❌ |
Wheels
There is a choice of 2 different wheel styles.
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Wheel I - Inner | 4 | eSun ABS+ (Cold White) | ❌ | |
| Wheel I - Outer | 4 | eSun ABS+ (Cold White) | ❌ | |
| Wheel I - wheel Hub | 4 | eSun ABS+ (Black) | ❌ | |
| Wheel G - inner Rim | 4 | eSun ABS+ (Silver) | ❌ | |
| Wheel G - outer Rim | 4 | eSun ABS+ (Silver) | ❌ |
Hitch
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Hitch Cardan A | 1 | eSun ABS+ (Silver) | ❌ | |
| Hitch Cardan B | 1 | eSun ABS+ (Silver) | ❌ | |
| Pole Attachment | 1 | eSun ABS+ (Silver) | ❌ |
Spare Wheel
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Spare Wheel Mount | 1 | eSun ABS+ (Black) | ❌ |
Storage Box
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Storage Box | 1 | eSun ABS+ (Black) | ❌ | |
| Storage Box Cover | 1 | eSun ABS+ (Black) | ❌ |
Loading Ramps
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Ramp | 2 | eSun ABS+ (Silver) | ❌ |
Road Car Pad
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Road Car Pad - front | 2 | eSun ABS+ (Black) | ❌ | |
| Road Car Pad - rear | 2 | eSun ABS+ (Black) | ❌ |
Landy Rear Bumper
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Rear Bumper | 1 | eSun ABS+ (Black) | ❌ | |
| Rear frame end | 1 | eSun ABS+ (Black) | ❌ | |
| Trailer Hitch | 1 | eSun ABS+ (Black) | ❌ | |
| Trailer Hitch Lock | 1 | eSun ABS+ (Red) | ❌ |
Street Accessory
Image © 2022 3D Sets
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Road Block Mini | 3 | eSun ABS+ (Red) | ❌ | |
| Road Block Mini | 3 | eSun ABS+ (Cold White) | ❌ | |
| Traffic Cone Mini | 4 | eSun ABS+ (Orange) | ❌ |
Tip
Stripes on the Traffic Cone can be achieved by making a Filament Change (M600) at layers 73, 113, 166 & 206.
Storage System
Image © 2022 3D Sets
Sourcing Parts
Misc
| Item | Quantity | Received | Notes |
|---|---|---|---|
| 3mm Hardboard 600x320 | 2 | 4 | |
| 3mm Hardboard 600x270 | 2 | 4 | |
| 3mm Hardboard 284x320 | 2 | 4 | |
| Textile strap 40-45 mm wide, 125-130 cm long | 1 | 2 | Have 50mm wide, will modify the mount to fit |
Fasteners
| Item | Quantity | Received | Notes |
|---|---|---|---|
| M3x8 BHCS | 4 | 91 | |
| M3x12 BHCS | 58 | 147 |
Printing Parts
| Item | Quantity | Material | Printed | Notes |
|---|---|---|---|---|
| Click-On Corner top left 4 A | 1 | eSun ABS+ (Red) | ❌ | |
| Click-On Corner top right 4 A | 1 | eSun ABS+ (Red) | ❌ | |
| Click-On Corner top left 4 B | 1 | eSun ABS+ (Red) | ❌ | |
| Click-On Corner top right 4 B | 1 | eSun ABS+ (Red) | ❌ | |
| Corner top right 3 | 1 | eSun ABS+ (Red) | ❌ | |
| Connector | 2 | eSun ABS+ (Red) | ❌ | |
| Corner bottom left 1 | 1 | eSun ABS+ (Red) | ❌ | |
| Corner bottom right 1 | 1 | eSun ABS+ (Red) | ❌ | |
| Corner bottom left 2 | 1 | eSun ABS+ (Red) | ❌ | |
| Corner bottom right 2 | 1 | eSun ABS+ (Red) | ❌ | |
| Corner top left 3 | 1 | eSun ABS+ (Red) | ❌ | |
| Corner top right 3 | 1 | eSun ABS+ (Red) | ❌ | |
| Side Handle | 2 | eSun ABS+ (Red) | ❌ | |
| Tyre Support | 4 | eSun ABS+ (Red) | ❌ |
Important
I have modified the 3D Sets Side Handle to accept a wider strap as I already have a 50mm strap that is wider than the one in the BOM. Shared with permission.